Asher Burkin: Difference between revisions

From makerspace.tulane.edu
Jump to navigation Jump to search
Line 69: Line 69:


====In the lab====
====In the lab====
This is a picture of the piece I made for the labs spectrometer. In the picture you can see the NeHe beam on the surface of the mirrors and on the prism that is being held by the piece I milled. The prism is not clean for alignment purposes.  
Below is a picture of the piece I made for the labs spectrometer in action. In the picture you can see the NeHe beam on the surface of the mirrors and on the prism that is being held by the piece I milled. The prism is not clean for alignment purposes.  


[[File:Optics lab in lab.jpg|350px]]
[[File:Optics lab in lab.jpg|350px]]

Revision as of 01:18, 7 January 2022

MakerSpace Fabrication Technician

Email: aburkin@tulane.edu

Major: Engineering Physics

Certificate: Mechanical Engineering

LinkedIn: in/asherburkin

Profile

Maker Skills

Projects

CNC Mill

I have been working on creating some of the pieces in the Titans of CNC course to develop a deeper understanding of CAM. When I first started milling, I quickly learned how steep of a learning curve it is. After countless hours of watching videos on how to use CAM, reading the CNC Mill instruction manual, and lots of trial and error, I finally understand the inner workings of this machine and have realized how crucial this understanding is to becoming a good machinist. Through this process I now know what feeds and speeds work best for different tools, the optimal depths of cuts, adaptive clearing methods for pockets and contours, and most importantly, how hard I can push the machine to get the best results.

These are the final versions of the first and second piece I milled from the Titans of CNC course.


CNC MILL Repair

I identified, rewired and fixed Tulane Makerspaces' CNC Mill.


Center

The Rubtsov Group (Optics Lab)

This lab came to me because they needed a new part for their labs spectrometer to hold a prism accurately. A few graduate students tried to make this part on a manual mill, but they were not getting the tolerances needed. I created the CAM and milled their part, which hit the correct tolerances needed.


Center

In the lab

Below is a picture of the piece I made for the labs spectrometer in action. In the picture you can see the NeHe beam on the surface of the mirrors and on the prism that is being held by the piece I milled. The prism is not clean for alignment purposes.

CNC Lathe And CNC Mill

The Ferris Lab (Ecology Lab)

I worked closely with one of the lab members in The Ferris Lab, Bolivar Aponte, on this project. Bolivar needed to make something to hold the spectrometry probe in a way that when taking measurements of flowers, the probe and holder would not crush the pedals. The original set up of probe and holder was a slab of aluminum sitting on top of the flower with a small hole to hold the probe. We came up with a way that would reduce the amount of surface area on top of the flowers by angling the larger holder by 45 degrees and then making a cylindrical holder for the probe so that there is only a small surface area sitting on the flower. We needed to make this cylindrical holder so that there is no light penetrating to the measurement area. the probe itself is a cylinder with a small hole at the end where light comes out to take measurements. This set up we created will not only preserve the flowers better, but also make it easier to select the sample area.

Center

Making of the probe holder.

Center

Machining all the surfaces flat relative to each other.

Center

Final product. We are still in revision and continuing this project to fine tune the process.

Water Jet

I worked on a project to cut this 1 inch thick, cold rolled slab of steel, into a new base to hold a vice. The entire operation took around 45 minutes. The garnet container needed to be refilled over 10 times and I was constantly checking the orientation of the the water jet cutter. In setting up the program, I had to take into account the kerf of the water as the holes and size of the base needed to run true to the design. I ran a very slow cut for this operation to ensure the the deflection of the water, as it first goes through the steel, does not curve too much through the cut.


Center

Quick Solution during a job


Casting

I modeled and 3D printed a shape with large draft angles to go through the process of forming the mold and pouring the pewter. I then 3D printed a tiki head to do another casting with the rest of the pewter I had.


Center

Center

Center

Center

Laser Cutting

Truss Project

I made a Pratt Truss. I designed each component for the truss and then assembled the truss, connecting everything with screws, washers, and nuts.

Center