Difference between revisions of "Ninja Log"

From makerspace.tulane.edu
Jump to navigation Jump to search
Line 1: Line 1:
 +
Ultimakers are referred to as 1,2,3 in relation to their position from left to right
 +
 
5/17/2017
 
5/17/2017
 
9:00-
 
9:00-
  
Error Message on the Ultimaker 2+ Read:  
+
Error Message on the Ultimaker 2+ (1) Read:  
 
"X or Y switch broken"
 
"X or Y switch broken"
 
1) Pressed "Home Head" under advanced settings to determine the source of the problem.
 
1) Pressed "Home Head" under advanced settings to determine the source of the problem.
Line 26: Line 28:
 
-Hook up  
 
-Hook up  
  
Print failed mid-way through:
+
Ultimaker 2+ (3) print failed mid-way through:
 
-Appeared to be an extrusion problem  
 
-Appeared to be an extrusion problem  
 
-Filament connection was still intact in the rear of the machine
 
-Filament connection was still intact in the rear of the machine
Line 39: Line 41:
 
-Ensure to check the "Air Assist" box when color mapping. Otherwise, no smoke will blow from the nozzle and flames will occur  
 
-Ensure to check the "Air Assist" box when color mapping. Otherwise, no smoke will blow from the nozzle and flames will occur  
  
Print wasn't extruding
+
Ultimaker 2+ (1) Print wasn't extruding
 
-After fixing the X and Y switch, a print was started that didn't extrude
 
-After fixing the X and Y switch, a print was started that didn't extrude
 
-heated the nozzle and wasn't able to move the material
 
-heated the nozzle and wasn't able to move the material
-checked in the back and saw that the filament had snapped
+
-checked in the back and saw that the filament had snapped because there wasn't much filament left in the spool
 
-attempted to reverse but there was no movement
 
-attempted to reverse but there was no movement
 
-used pliers to remove the filament from its housing
 
-used pliers to remove the filament from its housing
-put in new filament and worked like a charm
+
-put in a new spool of filament and loaded it into the system
 +
-

Revision as of 18:33, 17 May 2017

Ultimakers are referred to as 1,2,3 in relation to their position from left to right

5/17/2017 9:00-

Error Message on the Ultimaker 2+ (1) Read: "X or Y switch broken" 1) Pressed "Home Head" under advanced settings to determine the source of the problem. 2) Stepper Motor ground as it tried to continue to move the printhead 3) Turned off the machine, checked to see if the X and Y switches were being activated when the printhead reached "home" 4) Once the switches were verified to be mechanically activated, the print-head was moved to the bottom right corner of the machine. Pressed "Home Head" and held each of the switches to determine if they halted the movement of the printhead. 5) The x-axis movement ceased but the y-axis continued to jog. 6) This indicated that the error was caused by the Y switch 7) Disconnected the printer from power and un-screwed the Y switch 8) Mechanically everything seemed to be in order so we grabbed a Multimeter to test the switch 9) There was no distinction between when the switch was pressed and when it wasn't (OL both ways) 10) Unsecured the two electrical connections and saw that one of the wires had broken off 11) Grabbed the sautering gun and sautered it to its connection 12) Checked the other connection and saw that it was in need of the same operation 13) checked the resistance across and saw that it was zero 14) resecured the left switch to the Ultimaker 2+ 15) tested to see if "Home Head" worked 16) Everything back in order


Laser Printer produced flames, indicating that the compressed air "Air Assist Feature" isn't properly working -Check to see if PSI is around 30 -Hook up

Ultimaker 2+ (3) print failed mid-way through: -Appeared to be an extrusion problem -Filament connection was still intact in the rear of the machine -Reversed material, saw that the filament was grinding and had gotten stuck -Cut off the spoiled filament and reloaded it into the machine -Saw a small blockage in the printhead nozzle -extruded a little extra of the filament from its chamber and forced it down to push through the blockage -blockage cleared easily and I extruded another five or so rotations to make sure all was good.


Color Mapping -Ensure to check the "Air Assist" box when color mapping. Otherwise, no smoke will blow from the nozzle and flames will occur

Ultimaker 2+ (1) Print wasn't extruding -After fixing the X and Y switch, a print was started that didn't extrude -heated the nozzle and wasn't able to move the material -checked in the back and saw that the filament had snapped because there wasn't much filament left in the spool -attempted to reverse but there was no movement -used pliers to remove the filament from its housing -put in a new spool of filament and loaded it into the system -